If you are still unsure, it is not a PP
Sealing feels like progress, so people seal too early. If the shoulder is still a discussion, you do not have a pre-production sample. You have a fit sample that happens to be wearing some of the bulk trims. An email that says approved, under photographs, is not a seal either. The seal is the garment both sides can put on a table. Inspection will hold bulk to that garment, including the part you meant to 'just tidy'.
How the seal sits in the order — fit approved, bulk cloth and trims in house — is on order stages. This is the designer's list of what has to be finished before that signature.
The cloth has to be the bulk cloth
A pre-production sample is cut in the bulk cloth and the bulk trims. Something close can be approved for fit. It cannot be the standard for hand, show-through, seam slippage or shade. If the bulk cloth is not in the building, move the seal. Do not sign a substitute and hope the bulk 'feels the same'. It will not, and the argument will happen at inspection, when the order is already sewn.
Fusing, stitch and pocket
Write the fusing before you seal: collar, placket, waistband, chest piece, hem. Fused as standard means the room's standard, which may be lighter than the hand you liked on the proto. A heavier chest piece after the seal is a different jacket. It changes the roll and the shoulder, and it will not match the sample your inspector is holding.
If the topstitch is the design — the lapel pick, a raised trouser seam — the gauge belongs on the seal. A note in bulk that the stitch looks too fine arrives after half the order is sewn. The pocket, too: jet or patch, the bag, the height. 'Same as the photo' is how two pockets leave the floor.
Womenswear: the roll, and the lining
A lapel roll is pressed into the bridle. You do not redraw it on a finished jacket and call it the same style. If the roll is not the one you want, say so on this sample, with the amount, before anyone seals it. The way to write that note is in fit comments a pattern room can cut from.
Dress lining: how long against the shell, and whether it is caught at the hem or hanging free. A lining sealed too long is what you will receive. Shortening it in bulk is a rework.
Menswear: the fused collar, and the inside of the waistband
The shirt is the collar. A bulk lot on a softer fuse will collapse at the neck even when every measurement passes. Seal the fused collar, not a proto that was pad-stitched by hand because the fuse had not come in.
On the trouser, name the waistband: curtain or none, belt loops or side adjusters, and the finish on the inside. Trousers are rejected for the inside of the waistband more often than the sketch suggests, because that is what the customer feels putting them on. The rise itself should already have been settled in fit. Do not leave it as 'we will ease it in bulk'.
What you may still change
A button colour from a card both sides have already signed. Care-label wording, if your compliance team corrects it and the position does not move. A carton mark. Not the pad, not the rise, not the cloth. Those are a new sample, written and priced as one, or they are a dispute when the goods are packed.
| You want to change | What it actually is |
|---|---|
| Button colour on an approved card | An approval, if the card was already signed |
| Care text, position unchanged | A label correction |
| Shoulder pad, roll, rise, fusing or cloth | A new pre-production sample |
| Slim it a centimetre in bulk | A new pattern, and a broken seal |
| Topstitch gauge | A new standard; bulk already sewn will not match |
Frequently asked questions
What should a designer freeze before a sealed pre-production sample?
The block and ease, the actual bulk cloth and trims, the fusing, the visible stitch, and the pocket and closure. A sample in substitute cloth can approve fit. It cannot be the seal.
Can we still adjust fit after the PP is sealed?
Not quietly. A change to shoulder, rise, fusing or cloth is a new sample. A trim colour from a card both sides already approved is not.
Why not seal in a similar fabric to save the date?
Because inspection and the reorder will be judged against that sample. Hand, fusing show-through and shade will not match, and the argument starts when the order is already sewn.